Wireless control over a long distance with the LoRa modem
A Practical Telemetry System
To demonstrate the utility of the LoRa modem module, I packaged two Raspberry Pis into waterproof plastic boxes. One Pi was set up as the transmitter running the switch application, with two control switches and an LED mounted externally (Figure 5). Toggling either switch causes a packet to be sent to the receiver. The LED flashes when the transmitter receives an ACK from the receiver.
The second Pi runs the relay application and has a small module with two relays [11] wired and mounted internally, and a single LED mounted externally that flashes on reception of a valid packet from the transmitter (Figure 6).
This is pretty much the simplest application of LoRa. You can configure a lot more, such as an example spreading factor, channel frequency, and bandwidth that allow you to tailor the radio link to a specific situation. I was able to outfit both modules to run on solar-charged battery packs (Figure 7).
Software
The software for this system builds on the test software described earlier. The complete code for both switch and relay applications, together with a makefile are available for download from my GitHub page [12]. Only the end-user parts of the code are listed here; for brevity, I have omitted error-reporting code.
Listing 1 shows the switch module. This module sets up the required GPIO pins and then enters a loop looking for pin changes from the external switches. In detecting a change, it sends a message to the receiver to turn on or off the associated relay.
Listing 1
The Switch
§§number 01 #include "SX1272.h" 02 #include <stdio.h> 03 #include <syslog.h> 04 05 int main () 06 { 07 // set up the LoRa modem 08 sx1272.ON(); 09 sx1272.setMode(4); 10 sx1272.setHeaderON(); 11 sx1272.setChannel(CH_17_868); 12 sx1272.setCRC_ON(); 13 sx1272.setPower('M'); 14 sx1272.setNodeAddress(3); 15 16 // set up GPIO: 2 inputs and one output 17 bcm2835_gpio_fsel(RPI_V2_GPIO_P1_18,BCM2835_GPIO_FSEL_INPT); 18 bcm2835_gpio_set_pud(RPI_V2_GPIO_P1_18,BCM2835_GPIO_PUD_UP); 19 bcm2835_gpio_fsel(RPI_V2_GPIO_P1_08, BCM2835_GPIO_FSEL_INPT); 20 bcm2835_gpio_set_pud(RPI_V2_GPIO_P1_08, BCM2835_GPIO_PUD_UP); 21 bcm2835_gpio_fsel(RPI_V2_GPIO_P1_16,BCM2835_GPIO_FSEL_OUTP); 22 23 // get the current switch states 24 uint8_t oldLev_08=bcm2835_gpio_lev(RPI_V2_GPIO_P1_08); 25 uint8_t oldLev_18=bcm2835_gpio_lev(RPI_V2_GPIO_P1_18); 26 27 while(1) 28 { 29 // get the new states 30 uint8_t lev_08=bcm2835_gpio_lev(RPI_V2_GPIO_P1_08); 31 uint8_t lev_18=bcm2835_gpio_lev(RPI_V2_GPIO_P1_18); 32 33 //if state is different, send message and update 34 if(lev_08 != oldLev_08) 35 { 36 char *msg=(char*)(!lev_08?"ON0":"OFF0"); 37 syslog(LOG_USER,msg); 38 uint8_t e = sx1272.sendPacketTimeoutACKRetries(8, msg); 39 40 if(e==0) 41 { 42 // flash the LED 43 bcm2835_gpio_set(RPI_V2_GPIO_P1_16); 44 bcm2835_delay(500); 45 bcm2835_gpio_clr(RPI_V2_GPIO_P1_16); 46 // update rthe state 47 oldLev_08=lev_08; 48 } 49 } 50 51 //if state is different, send message and update 52 if(lev_18 != oldLev_18) 53 { 54 char *msg = (char*)(!lev_18?"ON1":"OFF1"); 55 syslog(LOG_USER,msg); 56 uint8_t e=sx1272.sendPacketTimeoutACKRetries(8, msg); 57 58 if(e==0) 59 { 60 // flash the LED 61 bcm2835_gpio_set(RPI_V2_GPIO_P1_16); 62 bcm2835_delay(500); 63 bcm2835_gpio_clr(RPI_V2_GPIO_P1_16); 64 // update rthe state 65 oldLev_18=lev_18; 66 } 67 } 68 69 // wait a bit & repeat 70 bcm2835_delay(500); 71 } 72 }
Listing 2 shows the relay module, which sets up the required GPIO pins and then enters a loop listening for messages from the switch module. In detecting a message, it turns on or off the associated relay.
Listing 2
The Relay
§§number 01 #include "SX1272.h" 02 #include <stdio.h> 03 #include <string.h> 04 05 int main () 06 { 07 // set up the LoRa modem 08 sx1272.ON(); 09 sx1272.setMode(4); 10 sx1272.setHeaderON(); 11 sx1272.setChannel(CH_17_868); 12 sx1272.setCRC_ON(); 13 sx1272.setPower('M'); 14 sx1272.setNodeAddress(8); 15 16 // set up GPIO: 3 outputs 17 bcm2835_gpio_fsel(RPI_V2_GPIO_P1_26,BCM2835_GPIO_FSEL_OUTP); 18 bcm2835_gpio_fsel(RPI_V2_GPIO_P1_18,BCM2835_GPIO_FSEL_OUTP); 19 bcm2835_gpio_fsel(RPI_V2_GPIO_P1_16,BCM2835_GPIO_FSEL_OUTP); 20 21 // turn both relays off 22 bcm2835_gpio_clr(RPI_V2_GPIO_P1_18); 23 bcm2835_gpio_clr(RPI_V2_GPIO_P1_26); 24 25 while(1) 26 { 27 // wait for an incoming message and sens an ACK 28 if (sx1272.receivePacketTimeoutACK(10000) == 0) 29 { 30 // get the packet data and act on it 31 char *msg = (char *)sx1272.packet_received.data; 32 printf("%s\n", msg); 33 sx1272.getRSSI(); 34 35 if(strcmp("ON0", msg)==0) 36 { 37 bcm2835_gpio_set(RPI_V2_GPIO_P1_18); 38 } 39 40 if(strcmp("OFF0", msg)==0) 41 { 42 bcm2835_gpio_clr( RPI_V2_GPIO_P1_18); 43 } 44 45 if(strcmp("ON1", msg)==0) 46 { 47 bcm2835_gpio_set(RPI_V2_GPIO_P1_26); 48 } 49 50 if(strcmp("OFF1", msg)==0) 51 { 52 bcm2835_gpio_clr(RPI_V2_GPIO_P1_26); 53 } 54 55 // flash the LED 56 bcm2835_gpio_set(RPI_V2_GPIO_P1_16); 57 bcm2835_delay(500); 58 bcm2835_gpio_clr(RPI_V2_GPIO_P1_16); 59 } 60 } 61 }
Next Steps
For further development, I should point out that LoRa data flow is truly bidirectional. There's nothing to stop the remote node, in this case the relay node, from sending unsolicited packets to the switch node. So any node can be both a sender and a receiver. It is also possible to send broadcast packets to any node listening on the same channel, as well as to send unacknowledged packets, similar to TCP/IP's UDP packets. A complete, freely available WAN implementation called LoRaWAN [13] even turns a bunch of LoRa nodes and a gateway node into a true network, with semantics very similar to TCP/IP.
« Previous 1 2 3 Next »
Buy this article as PDF
(incl. VAT)
Buy Linux Magazine
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters
Support Our Work
Linux Magazine content is made possible with support from readers like you. Please consider contributing when you’ve found an article to be beneficial.
News
-
Endless OS 6 has Arrived
After more than a year since the last update, the latest release of Endless OS is now available for general usage.
-
Fedora Asahi 40 Remix Available for Macs with Apple Silicon
If you've been anticipating KDE's Plasma 6 for your Apple Silicon-powered Mac, then you're in luck.
-
Red Hat Adds New Deployment Option for Enterprise Linux Platforms
Red Hat has re-imagined enterprise Linux for an AI future with Image Mode.
-
OSJH and LPI Release 2024 Open Source Pros Job Survey Results
See what open source professionals look for in a new role.
-
Proton 9.0-1 Released to Improve Gaming with Steam
The latest release of Proton 9 adds several improvements and fixes an issue that has been problematic for Linux users.
-
So Long Neofetch and Thanks for the Info
Today is a day that every Linux user who enjoys bragging about their system(s) will mourn, as Neofetch has come to an end.
-
Ubuntu 24.04 Comes with a “Flaw"
If you're thinking you might want to upgrade from your current Ubuntu release to the latest, there's something you might want to consider before doing so.
-
Canonical Releases Ubuntu 24.04
After a brief pause because of the XZ vulnerability, Ubuntu 24.04 is now available for install.
-
Linux Servers Targeted by Akira Ransomware
A group of bad actors who have already extorted $42 million have their sights set on the Linux platform.
-
TUXEDO Computers Unveils Linux Laptop Featuring AMD Ryzen CPU
This latest release is the first laptop to include the new CPU from Ryzen and Linux preinstalled.