Build a VPN Tunnel with WireGuard
Building an Interface
The next step is to create one virtual network interface per device for WireGuard. This is the equivalent of eth0
or wlan0
. However, since traffic is tunneled separately with WireGuard, the system requires one interface for routing. The default for the first interface in WireGuard is wg0
(which we will use for simplicity's sake). If you prefer a different name, this is not a problem as long as you use it consistently.
The interface you created requires a specific IP range. In order to distinguish it from the 192.168.<x>.<y> common on LANs, use IPs from the private network address range 10.0.10.x [7] for wg0
, which you then make available to the outside world via masquerading [8]. For the configuration, save Listing 4 (server) and Listing 5 (client) in the /etc/wireguard/wg0.conf
file.
Listing 4
Server Configuration
[Interface] Address = 10.0.10.1/24,fd42:42:42::1/64 SaveConfig = true PrivateKey = <Key from client1.key> ListenPort = 51820 PostUp = iptables -A FORWARD -i wg0 -j ACCEPT; iptables -t nat -A POSTROUTING -j MASQUERADE; iptables -A FORWARD -o wg0 -j ACCEPT PostUp = ip6tables -A FORWARD -i wg0 -j ACCEPT; ip6tables -t nat -A POSTROUTING -j MASQUERADE; ip6tables -A FORWARD -o wg0 -j ACCEPT PostDown = iptables -F; iptables -t nat -F PostDown = ip6tables -F; ip6tables -t nat -F DNS = <IP Address of the WLAN Router> [Peer] PublicKey = <Key from client2.pub> AllowedIPs = 10.0.10.2/32,fd42:42:42::/64
Listing 5
Client Configuration
[Interface] Address = 10.0.10.2/32,fd42:42:42::2/64 PrivateKey = <Key from client2.key> DNS = 10.0.10.1 [Peer] PublicKey = <Key from client1.pub> Endpoint = <beispiel.dyndns.com>:51820 AllowedIPs = 0.0.0.0/0,::/0 PersistentKeepalive = 20
Be sure to enter the cryptographic keys from the key files. You will also want to tell the server to use the WLAN router as a DNS server using the DNS = [...]
line. The WireGuard client, on the other hand, needs to use the DNS = 10.0.10.1
option to query the WireGuard computer as its DNS server. The server configuration includes the same rules for starting up and shutting down the interface.
WireGuard uses port 51820 as the default port. If you want to use a different port, adjust the ListenPort = 51820
line accordingly. You then control the connection setup with the command:
sudo wg-quick up wg0
You can shut down the VPN again by typing:
sudo wg-quick down wg0
The sudo wg
command tells WireGuard to display information on the current status (Figure 3). To activate wg0
automatically at system startup time, type the following command on both computers:
sudo systemctl enable wg-quick@wg0
UFW
The easiest way to configure the port sharing settings is via the Uncomplicated Firewall (UFW) iptables front end (Listing 6), which is preinstalled on Ubuntu and included in most distributions' package sources. There is also the Gufw graphical interface. After installation, if necessary, allow port 22/TCP for SSH on both devices and open 51820/UDP or your chosen port (Figure 4).
Listing 6
Configuring Port Sharing with UFW
$ sudo ufw allow 22/tcp $ sudo ufw allow <51820>/udp ### Or the port chosen by the system $ sudo ufw enable $ sudo ufw status verbose Status: Active Logging: on (low) Default: deny (incoming), allow (outbound), deny (sent) New profiles: skip To Action From -- ------ --- 22/tcp ALLOW IN Anywhere 51820/udp ALLOW IN Anywhere 22/tcp (v6) ALLOW IN Anywhere (v6) 51820/udp (v6) ALLOW IN Anywhere (v6)
Conclusions
If you have no errors in the configuration, you should be able to ping the other IP address. From our personal experience, we found that configuration errors can happen easily. However, WireGuard can be set up quite quickly with about an hour of concentrated work. You can then extend the configuration to include additional clients, such as Android smartphones, using the same principle.
Infos
- WireGuard: https://www.wireguard.com/
- "Linux Torvalds Is Hoping WireGuard Will Be Merged Sooner Rather Than Later" by Michael Larabel, August 3, 2018, https://www.phoronix.com/scan.php?page=news_item&px=Linus-Likes-WireGuard
- ChaCha20: https://cr.yp.to/chacha.html
- Curve25519: https://cr.yp.to/ecdh.html
- Installation: https://www.wireguard.com/install
- DynDNS Service: https://dyndnss.net/eng/
- Private IP addresses: https://en.wikipedia.org/wiki/Private_network
- Masquerading: https://www.tldp.org/HOWTO/IP-Masquerade-HOWTO/ipmasq-background2.1.html
« Previous 1 2 3
Buy this article as PDF
(incl. VAT)
Buy Linux Magazine
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters
Support Our Work
Linux Magazine content is made possible with support from readers like you. Please consider contributing when you’ve found an article to be beneficial.
News
-
Fedora 41 Beta Available with Some Interesting Additions
If you're a Fedora fan, you'll be excited to hear the beta version of the latest release is now available for testing and includes plenty of updates.
-
AlmaLinux Unveils New Hardware Certification Process
The AlmaLinux Hardware Certification Program run by the Certification Special Interest Group (SIG) aims to ensure seamless compatibility between AlmaLinux and a wide range of hardware configurations.
-
Wind River Introduces eLxr Pro Linux Solution
eLxr Pro offers an end-to-end Linux solution backed by expert commercial support.
-
Juno Tab 3 Launches with Ubuntu 24.04
Anyone looking for a full-blown Linux tablet need look no further. Juno has released the Tab 3.
-
New KDE Slimbook Plasma Available for Preorder
Powered by an AMD Ryzen CPU, the latest KDE Slimbook laptop is powerful enough for local AI tasks.
-
Rhino Linux Announces Latest "Quick Update"
If you prefer your Linux distribution to be of the rolling type, Rhino Linux delivers a beautiful and reliable experience.
-
Plasma Desktop Will Soon Ask for Donations
The next iteration of Plasma has reached the soft feature freeze for the 6.2 version and includes a feature that could be divisive.
-
Linux Market Share Hits New High
For the first time, the Linux market share has reached a new high for desktops, and the trend looks like it will continue.
-
LibreOffice 24.8 Delivers New Features
LibreOffice is often considered the de facto standard office suite for the Linux operating system.
-
Deepin 23 Offers Wayland Support and New AI Tool
Deepin has been considered one of the most beautiful desktop operating systems for a long time and the arrival of version 23 has bolstered that reputation.