Monitor your old Linux devices
Watching Grampa

© Lead Image © lightwise, 123RF.com
Create monitoring dashboards with SSH, command-line tools, and Node-RED.
Some excellent technologies and packages are available for monitoring computer hardware. For medium to large systems, the Simple Network Monitoring Protocol (SNMP) approach is usually the preferred solution. However if you have a smaller system with older or low-end servers, some excellent lightweight command-line monitoring utilities can be used instead.
These command-line utilities can be run remotely over Secure Shell (SSH) and the output parsed to return only the key data values, which can then be displayed graphically in a Node-RED web dashboard (Figure 1). In this article, I demonstrate examples that use the iostat
utility [1] to monitor CPU utilization and the lm-sensors package [2] and hddtemp
utility [3] to monitor temperatures on dashboards.
CPU Utilitization
The iostat
utility is part of the sysstat package and is probably already loaded on your older systems. If not, it can be installed by:
sudo apt-get install sysstat
The iostat
utility generates a report for CPU, device, and filesystem utilization. The output from this command can be parsed with some Bash statement to return just the key value of interest.
Listing 1 shows an example of how to grab the fourth line of output with sed (line 7) and parse the %idle value at the end of the line with awk (line 11) to get the sixth string item (line 12).
Listing 1
Parsing iostat Output
01 pete@lubuntu: ~$ iostat -c 02 Linux 4.15.0-72-generic (lubuntu) 2020-05-02 i686 (4 CPU) 03 avg-cpu: %user %nice %system %iowait %steal %idle 04 8.37 0.03 3.33 1.29 86.97 05 06 # Get 4th line of the iostat output 07 pete@lubuntu : ~$ iostat -c | sed -n 4p 08 8.36 0.03 3.33 1.29 0.00 86.99 09 10 # Now get the 6th string 11 pete@lubuntu : ~$ iostat -c | sed -n 4p | awk '{print $6}' 12 87.02
Chip-Based Temperature
To install the hardware sensors in the lm-sensors package, enter:
sudo apt-get install lm-sensors
After the package is installed, the software needs to detect which sensors are available for monitoring:
sudo sensors-detect
This step presents a number of prompts about which sensors need to be scanned. Once the scan step is complete, the sensors command returns results for all the hardware it found.
Specific sensors can be shown with the command:
sensors <chip name>
Listing 2 shows an example of the sensors
command being used to look at the dell_smm-virtual-0 chipset. The CPU temperature value (in line 5) can be parsed with grep
(line 10), which looks for the line that contains "CPU'; then, awk (line 14) outputs the second item of the string (line 15).
Listing 2
Parsing Sensor Data
01 pete@lubuntu: ~$ sensors dell_smm-virtual-0 02 dell_smm-virtual-0 03 Adapter: Virtual device 04 Processor Fan: 2687 RPM 05 CPU: +40.0°C 06 Ambient: +34.0°C 07 SODIMM: +33.0°C 08 09 # Get the CPU temperature 10 pete@lubuntu: ~$ sensors dell_smm-virtual-0 | grep 'CPU' 11 CPU: +40.0°C 12 13 # Return just the temperature 14 pete@lubuntu: ~$ sensors dell_smm-virtual-0 | grep 'CPU' | awk '{print $2}' 15 +40.0°C
Hard Drive Temperature
The hddtemp hard drive temperature monitoring package is installed with:
sudo apt-get install hddtemp
By default, hddtemp requires superuser rights, so to make the results available to non-superusers use:
sudo chmod u+s /usr/sbin/hddtemp
To see the temperature of a hard drive, enter its device name. For example, to see /dev/sda
, use:
$ hddtemp /dev/sda /dev/sda: WDC WD3200BPVT-75JJ5T0: 34°C
Again, you can use the awk
command to parse the output to get just the temperature. For this example, the temperature is the fourth item of the string, so the command displays that value as shown here:
$ hddtemp /dev/sda | awk '{print $4}' 34°C
Buy this article as PDF
(incl. VAT)
Buy Linux Magazine
Direct Download
Read full article as PDF:
Price $2.95
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters
Support Our Work
Linux Magazine content is made possible with support from readers like you. Please consider contributing when you've found an article to be beneficial.
News
-
Linux Mint Finally Receiving Support for Gestures
If you use the Linux Mint Cinnamon desktop, you'll be thrilled to know that 21.2 is getting support for gestures on touchscreen devices and touchpads.
-
An All-Snap Version of Ubuntu is In The Works
Along with the standard deb version of the open-source operating system, Canonical will release an-all snap version.
-
Mageia 9 Beta 2 Ready for Testing
The latest beta of the popular Mageia distribution now includes the latest kernel and plenty of updated applications.
-
KDE Plasma 6 Looks to Bring Basic HDR Support
The KWin piece of KDE Plasma now has HDR support and color management geared for the 6.0 release.
-
Bodhi Linux 7.0 Beta Ready for Testing
The latest iteration of the Bohdi Linux distribution is now available for those who want to experience what's in store and for testing purposes.
-
Changes Coming to Ubuntu PPA Usage
The way you manage Personal Package Archives will be changing with the release of Ubuntu 23.10.
-
AlmaLinux 9.2 Now Available for Download
AlmaLinux has been released and provides a free alternative to upstream Red Hat Enterprise Linux.
-
An Immutable Version of Fedora Is Under Consideration
For anyone who's a fan of using immutable versions of Linux, the Fedora team is currently considering adding a new spin called Fedora Onyx.
-
New Release of Br OS Includes ChatGPT Integration
Br OS 23.04 is now available and is geared specifically toward web content creation.
-
Command-Line Only Peropesis 2.1 Available Now
The latest iteration of Peropesis has been released with plenty of updates and introduces new software development tools.