Integrate hardware components with pluggable systems
Plugged In
Ecosystems with pluggable Raspberry Pi modules, sensors, and displays are a great choice if you don't want to – or can't – solder but still want to extend your hardware.
If you use your Raspberry Pi to control sensors or displays, you will frequently have to deal with wiring problems or resort to using a soldering iron. Plug-and-play systems such as Adafruit STEMMA-QT [1], Seeed Grove [2], SparkFun Qwiic [3], and DFRobot Gravity [4] provide connection systems for electronic components. A system recently introduced by Tinkerforge [5] can also be plugged together, but it plays in a different league, because it comes with an additional microcontroller for management tasks on each module.
The systems I will discuss in this article offer special cable connections on the devices (Figure 1). Common to all systems are reverse-polarity-proof connectors and symmetrical cables. In other words, the cable has connectors that look identical on both sides, but they are not the same internally and only fit one way. Cables also are color coded, but this is not significant from a technical point of view.
Advantages and Disadvantages
Even though you have four manufacturers with four different pluggable systems, you do not have to make a decision and be tied to one ecosystem. However, caveat emptor still applies; I will look at the details a little later.
First, I'll look at the obvious advantages. Of great importance is the stable connection: The pluggable systems are self-locking, which is helpful not only during prototyping, but later when building solutions, as well. Even the classic jumper cables with Dupont connectors can sometimes come loose inside a housing, especially when exposed to vibrations or shocks.
The standardized connections offer another advantage. The widely used inter-integrated circuit (I2C) is standardized on the bus, but each breakout comes with its own sequence of voltage, ground, SDA, and SCL, usually because of the arrangement of the pins on the installed chip. The connector systems put an end to this setup; as a user, however, this convenience comes at the price of a larger breakout and more complicated cable routing.
Cable Only?
On closer inspection, the different systems are surprisingly compatible. The oldest system, Grove (2010), uses a proprietary four-pin connector with a pin spacing of 2mm. Adafruit's STEMMA connectors (2014), on the other hand, rely on four- or three-pin JST-PH connectors, a widely used system. However, Japanese solderless terminals (JST, although they were developed in Germany) is not a standard. Adafruit only rarely uses the original STEMMA; sensors in particular are only available with STEMMA-QT, which I'll get back to later.
The four-pin STEMMA connector is intended for I2C and the three-pin variant for pulse-width modulation (PWM)/analog/digital connections. The four-pin STEMMA is in principle cable-compatible with Grove thanks to an identical pin-out sequence, as well as with Gravity from DFRobot through the three-pin connection. STEMMA connectors – contrary to Adafruit's claim – do not match up with Grove connectors. Adapter cables can be made very easily, though.
To use the right terms, the plugs are the things with pins that sit on the components, whereas the connector on the cable is a socket, although this terminology is counterintuitive and not what people actually call them; thankfully, what people mean is usually clear from the context.
The small STEMMA variant, known as STEMMA-QT (2017), uses the JST-SH connector, with a pin spacing of only 1mm. QT (cutie) is an intentional play on words. The advantage of STEMMA-QT is that it takes up less space on the breakouts, which is offset by the disadvantage that the smaller connectors cannot handle as many plugging operations. JST does not publish an exact number, but it will be somewhere in the double-digit range.
Adafruit deliberately chose the STEMMA-QT connector format to be compatible with SparkFun's Qwiic (2017), both of which are limited to I2C only.
At the cable level, the systems from the four manufacturers form two groups: STEMMA, Grove, and Gravity use large connectors with 2mm spacing, and STEMMA-QT and Qwiic use JST-SH connectors with 1mm spacing. Adapter cables or special breakouts with matching connectors convert between the individual systems (Figure 2).
Fine Differences
Mechanical compatibility is not everything. For example, sensor and breakout components will only work with 3.3V or 5V. A normal BME280 sensor breakout (3.3V) will therefore not work on an Arduino Uno (5V) without a voltage converter; therefore, STEMMA-, Grove-, and Gravity-compatible controllers or devices come with voltage converters so that, as a user, you don't have to worry about the voltage. Qwiic only supports the 3.3V variant, so Qwiic sensors will not work with 5V microcontrollers.
Both Grove and Gravity use the four-pin connector for more than just I2C. For example, Grove has a double push button (Figure 3) on offer, but because STEMMA only supports I2C, there is little point in plugging a button like this into a STEMMA HAT (a hardware attached on top add-on board). The same is true for Gravity devices with a universal asynchronous receiver/transmitter (UART) connection.
All in all, however, the differences between the systems are not so major that hobbyists have to commit for all time. You can pick and choose components to suit needs and availability. Many I2C components are on offer simply because of SparkFun, with its more than 150 components. Apart from I2C, however, things look a little more sparse, because Adafruit does not offer much in terms of three-pin products, and DFRobot's Gravity components are difficult to get in Germany – which is why I chose Grove.
Buy this article as PDF
(incl. VAT)
Buy Linux Magazine
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters
Support Our Work
Linux Magazine content is made possible with support from readers like you. Please consider contributing when you’ve found an article to be beneficial.
News
-
Linux Servers Targeted by Akira Ransomware
A group of bad actors who have already extorted $42 million have their sights set on the Linux platform.
-
TUXEDO Computers Unveils Linux Laptop Featuring AMD Ryzen CPU
This latest release is the first laptop to include the new CPU from Ryzen and Linux preinstalled.
-
XZ Gets the All-Clear
The back door xz vulnerability has been officially reverted for Fedora 40 and versions 38 and 39 were never affected.
-
Canonical Collaborates with Qualcomm on New Venture
This new joint effort is geared toward bringing Ubuntu and Ubuntu Core to Qualcomm-powered devices.
-
Kodi 21.0 Open-Source Entertainment Hub Released
After a year of development, the award-winning Kodi cross-platform, media center software is now available with many new additions and improvements.
-
Linux Usage Increases in Two Key Areas
If market share is your thing, you'll be happy to know that Linux is on the rise in two areas that, if they keep climbing, could have serious meaning for Linux's future.
-
Vulnerability Discovered in xz Libraries
An urgent alert for Fedora 40 has been posted and users should pay attention.
-
Canonical Bumps LTS Support to 12 years
If you're worried that your Ubuntu LTS release won't be supported long enough to last, Canonical has a surprise for you in the form of 12 years of security coverage.
-
Fedora 40 Beta Released Soon
With the official release of Fedora 40 coming in April, it's almost time to download the beta and see what's new.
-
New Pentesting Distribution to Compete with Kali Linux
SnoopGod is now available for your testing needs