Raspberry Pi 3 Model B+ overview

Bluetooth 4.2

The RPi3B supported Bluetooth 4.1; thanks to the CYW43455, the RPi3B+ now offers Bluetooth 4.2 – that is, "Bluetooth Classic" and Bluetooth LE (Low Energy). Version 4.2 improves speed, privacy, and data security for Bluetooth LE. Compared with the previous version, the data packets are two and a half times faster and are capable of containing up to 10 times more data.

Bluetooth 4.1 already provides for easier connection of devices without a hub, but Bluetooth 4.2 takes this to a whole new level: The IPSP-supported 6LoWPAN (Internet Protocol Support Profile/IPv6 over low-power wireless personal area networks) takes IPv6 to small, low-performance devices for integration into the Internet of Things.

The Generic Attribute Profile (GATT) provides a smart Bluetooth gateway to the Internet. For example, a BLE 4.2 sensor can send and receive messages through the RPi3B+ as a gateway. Bluetooth beacons that attempt to track your device require explicit permission as of v4.2. The LE Secure Connections pairing option is also available as of Bluetooth 4.2.

Performance

I was only able test the RPi3B+ for this article with a pre-release image with wireless not yet enabled and the CPU still clocked at 1.2GHz. A test with the new software image is coming soon, and the performance values for the RPi3B+ should improve significantly. As Table 1 shows, though, they are already impressive.

Table 1

RPi3B+ vs. RPi3B Test Results

 

RPi3B

RPi3B+

Comment

Specifications

SoC

Broadcom BCM2837

Broadcom BCM2837B0

Quad-core Cortex-A53

CPU

Cortex-A53 at 1.2GHz

Cortex-A53 at 1.4GHz

RPi3B+ tested at 1.2GHz

RAM

1024MB LPDDR2

1024MB LPDDR2

LAN

10/100Mbps

1,000Mbps

USB 2.0

Power

5V, 2.5A

5V, 2.5A

Micro-USB

System

SysBench (seconds) (1)

93.05

92.86

Slower is better

SysBench (seconds) (2)

372.09

371.34

Slower is better

RAM

mbw, MEMCPY method (MiBps)

694.80

785.59

Higher is better

mbw, DUMB method (MiBps)

721.43

807.20

Higher is better

mbw, MCBLOCK method (MiBps)

1,086.91

1,287.24

Higher is better

Network (LAN)

iperf (Mbps) (3)

94

319

Higher is better

SD Card

hdparm, cached (MBps)

601.8

600.0

Higher is better

hdparm, disk reads (MBps)

21.6

21.7

Higher is better

Power

Idle

4.2W

7.6W

Under load

11.7W

14.0W

During SysBench (4)

(1) CPU – total time, 3 repeats with 4 threads(2) CPU – total time by event execution, 3 repeats with 4 threads(3) 3 repeats(4) 3 repeats with 4 threads

Both the RPi3B and RPi3B+ devices were tested with a SanDisk SD card (class 10) and an EM 231 energy monitor by MK Electronics. A keyboard and HDMI and Ethernet cables were connected. The remote station in the LAN was a GigE port on a laptop connected with a gigabit switch by TP Link.

Interesting Facts

To run all functions of the new RPi3B+, you definitely need new software: It does not boot with NOOBS before version 2.7.0 dated March 14, 2018. The developers are also working on a firmware update for Raspbian Jessie. Other distributions, like LibreELEC and RetroPie, will follow suit in time.

The 40-pin GPIO header stayed the same, so all extension HATs fit. As with the RPi3B and Pi Zero W, Bluetooth is connected via the UART (PL011). If you use the UART through the GPIO header, you should note the known limitations of its mini UART. Alternatively, swap the two UARTs via overlay or disable Bluetooth [4].

The RUN header previously had two pins, of which one was ground suitable for mounting a reset button. However, the power supply remained switched on. With the RUN pin continuously grounded, the CPU was off for all intents and purposes, but the hardware still consumed power.

In the RPi3B+, the ground pin was removed from this header and a new PEN (power enable) pin was added. If you connect it to ground, it completely drains the power from the board. The board then transitions to the lowest consumption state possible, making it useful for projects that operate with a battery and wake up using a microcontroller.

Buy this article as PDF

Express-Checkout as PDF
Price $2.95
(incl. VAT)

Buy Linux Magazine

SINGLE ISSUES
 
SUBSCRIPTIONS
 
TABLET & SMARTPHONE APPS
Get it on Google Play

US / Canada

Get it on Google Play

UK / Australia

Related content

  • A New Raspberry Pi Board

    The new board packs everything that you get in Raspberry Pi 3B+ in a smaller package.

  • Wireless Standards

    The IEEE 802.11 standards are at the center of the wireless revolution. The wireless alphabet starts with 802.11a and extends to 802.11n. Linux Magazine helps you get your wireless spelling right.

  • CubieTruck

    The CubieTruck small-board PC is a measuring instrument that copes well with Gigabit networks and offers a surprisingly affordable and efficient solution.

  • News

    In the news: Microsoft gets an Open Source Web browser; Canonical launches MicroK8s; A new Raspberry Pi board; OpenStack Foundation changes name of the OpenStack Summit; Red Hat Enterprise Linux 8 beta; and System76 announces a line of US-made PCs.

  • Build a Portable Android-based Raspberry Pi Station
comments powered by Disqus
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters

Support Our Work

Linux Magazine content is made possible with support from readers like you. Please consider contributing when you’ve found an article to be beneficial.

Learn More

News